Compelo Medical Devices is using cookies

We use them to give you the best experience. If you continue using our website, we'll assume that you are happy to receive all cookies on this website.

ContinueLearn More
Close

Produce superior ID finish in tubing with Sonobond’s Ultrasonic Tube Drawing System

Sonobond Ultrasonics announced today that its Tube Drawing System and components are specially designed to accommodate manufacturers of fine metal tubing used in syringe needles, as well as for medical devices and tubing products used in many other industries to transport critical fluids.

"In conventional tube drawing systems, lubricants are used to reduce friction between tooling and metal tubing," explains Sonobond president Janet Devine. "With our ultrasonic system, high-frequency vibrations create a continuous cycle of increasing and decreasing pressure between tooling and work piece, resulting in less friction and a reduction of force needed for the draw and consequently significant improvement in the internal surface finish of the tube, which is absolutely essential for critical fluid transmission. Optimum results are achieved when the ultrasonic activation is used in conjunction with ‘best practices’ such as lubricants."

Applying ultrasonic energy to tube drawing operations

In a standard rod draw operation, a controller first positions the tube to be drawn over a long, back support rod, terminated in a plug, so that the tube to be drawn can be loaded onto the machine. Draw carriage jaws then grasp the tube and pull it through a die, which is on the outside of the tube and aligned with the plug which is inside the tube, thinning the tube walls and achieving the desired wall thickness and internal diameter. Often multiple draws are required with progressively smaller dies and plugs to reach the desired tube size.

In an ultrasonic system, a power supply converts line power to high voltage, high frequency electrical power needed to drive the transducer, which is attached to a coupler at the back end of the back support rod and mounted on a carriage on the draw bench. The transducer converts electrical energy to vibratory energy. Waveguides or components – typically a tapered coupler and the back support rod, which holds the die and/or plug – carry the vibratory energy from the transducer to the plug. The waveguides are designed to resonate at the frequency of operation of the power supply and transducer, usually in the range from 15 to 28 kilohertz depending on the size of the rod and the tube being drawn.

"The ultrasonic energy reduces frictional forces between the forming tools, and also increases the plasticity of the metal being drawn," Devine explains.

Benefits of ultrasonic tube drawing

"Adding ultrasonic energy to a tube-drawing operation can reduce the draw force required, in some cases by up to 35 percent, and permit heavier reductions thereby reducing the number of draws required to achieve a finished product," notes Devine. Additionally, ultrasonic tube drawing eliminates sticking and slipping, also known as "chatter," which can lead to product loss. There’s less breakage, especially at start-up when frictional forces are highest. Draw speed can be increased as much as 400 percent. Most significantly — especially for medical applications — surface finishes on the ID of the tube can be improved to RMS (Root Mean Square) values of eight or better micro-inches.

Medical product applications

Sonobond Ultrasonics’ Tube Drawing System achieves superior tubing suitable for syringe needles and other sharps. Ultrasonically drawn fine tubing can also be used to produce implantable device components; in vitro diagnostic probes; bands for catheters and guidewires; heat-exchanger tubes for controlling blood temperature during surgery; micro-surgical tools; stents and other devices requiring tubing with a fine internal dimension finish.

Sonobond services

Sonobond Ultrasonics can evaluate your existing tube drawing operation, recommend components, or design a complete system for your existing or new drawbench. From initial inquiry, through installation and implementation, we offer ongoing superior customer service.

Leading the industry

A pioneer in ultrasonic technology, Sonobond holds more than 150 patents, including the first for ultrasonic metal welding in 1960, when the company was known as Aeroprojects. In the ensuing 55 years, Sonobond has established and maintained a well-earned reputation for innovative and quality-engineered products. Today, the company manufactures a complete line of ultrasonic welding and bonding equipment and tube-drawing components used by leading firms in the electrical, automotive, appliance, HVAC, solar, aerospace, filtration, medical, body armor and apparel industries.

Learn more

For more information about Sonobond and its products please visit www.SonbondUltrasonics.com. For immediate assistance and information on ultrasonic tube drawing, please call 800-323-1269, 610-696-4710, or email jdevine@SonobondUltrasonics.com.

Quick Contact

Top Products from